溶液噴射製備聚甲基丙烯酸丁酯纖維及其油性有機物吸附性能

文化大學機構典藏 CCUR > 理工學院 > 工學院 > 紡織工程學系 > 學報-華岡紡織期刊 > Item 987654321/36342

請使用永久網址來引用或連結此文件: https://irlib.pccu.edu.tw/handle/987654321/36342

題名:	溶液噴射製備聚甲基丙烯酸丁酯纖維及其油性有機物吸附性能 Preparation of Poly(butyl methacrylate) Fiber by Solution Blowing and Its Absorptive Performance to Oily Organic Compounds
作者:	封嚴王剛毅莊旭品張志飛
貢獻者:	紡工系
關鍵詞:	聚甲基丙烯酸丁酯溶液噴射油性有機物 Poly(butyl methacrylate) Solution Blowing Oily Organic Compound
日期:	2016-05
上傳時間:	2017-06-27 10:26:06 (UTC+8)
摘要:	採用懸浮聚合工藝製備聚甲基丙烯酸正丁酯（PBMA），以甲基丙烯酸β羥乙酯（HEMA）為物理交聯劑，二乙烯基苯（DVB）為化學交聯劑，N,N-二甲基乙醯胺（DMAc）為溶劑，製備紡絲溶液。採用溶液噴射法製備複合交聯結構PBMA 纖維，研究了交聯劑含量及種類對纖維形貌和結構的影響，探討了PBMA 纖維對柴油、機油與大豆油等油性有機物的吸附性能。結果表明，當熱空氣溫度為170℃，擠出速率為10ml/h，牽伸風壓為0.03MPa，抽吸風風量為2520m3/h 時，所得纖維直徑均勻，形態良好。對不同油品的吸附性能測試結果表明，纖維對柴油、大豆油和機油的飽和吸附率分別為14g/g、10g/g 和8g/g，且具有良好的拒水親油性。 Poly(butyl methacrylate) (PBMA) was synthesized by suspension polymerization. The spinning solution was prepared with hydroxyethyl methylacrylate(HEMA) as physical crosslinking agent, divinyl benzene(DVB) as chemical crosslinking agent and N, N - dimethyl acetamide as solvent. The PBMA fiber with composite crosslinking structure was made via solution blowing process and the influence of the crosslinking agent content on the fiber morphologies was discussed. The absorptive properties of the fiber to diesel oil, engine oil and soybean oil were also studied. The results showed that the fiber diameter was uniform when hot air temperature, extrusion rate, air pressure and suction wind volume was 170 ℃, 10 ml/h, 0.03 MPa and 2520 m3/h, respectively. For different oil absorption test, the saturated oil absorbency of the fiber to diesel oil, soybean oil and engine oil was 14g/g, 10g/g and 8g/g. Also the fiber presented good hydrophobic performance.
關聯:	華岡紡織期刊； 23卷4期 (2016 / 05 / 01) ， P218 - 222
顯示於類別:	[紡織工程學系] 學報-華岡紡織期刊

文件中的檔案:

檔案	描述	大小	格式	瀏覽次數
index.html		0Kb	HTML	62	檢視/開啟

檢視Licence

在CCUR中所有的資料項目都受到原著作權保護.

資料載入中.....