低溫燃料電池用Pt/C觸媒之電催化特性分析

文化大學機構典藏 CCUR > 理工學院 > 工學院 > 工學院 > 學報-華岡工程學報 > Item 987654321/35646

請使用永久網址來引用或連結此文件: https://irlib.pccu.edu.tw/handle/987654321/35646

題名:	低溫燃料電池用Pt/C觸媒之電催化特性分析 Electrocatalytic Characterization of Pt/C Catalysts Used in Low-Temperature Fuel Cells
作者:	何佩紋李鴻達徐沛紳施信民林仁斌
貢獻者:	化材系
關鍵詞:	白金電催化氫氣氧化一氧化碳燃料電池 platinum electrocatalysis hydrogen oxidation carbon monoxide fuel cells
日期:	2010-06
上傳時間:	2017-03-23 13:40:40 (UTC+8)
摘要:	本研究以膠體先驅物法製備低溫燃料電池用碳黑負載之奈米級鉑（Pt/C）觸媒，並以循環伏安法（CV）及旋轉電極（RDE）探討Pt/C觸媒上化學吸附的一氧化碳（CO）對氫氣氧化反應（HOR）的影響。以X-ray繞射分析儀（XRD）和穿透式電子顯微鏡（TEM）量測所製備的5.4～27.2wt% Pt/C觸媒之Pt 粒徑範圍為3.1～8.9 nm，其值比商用Pt/C觸媒中的略大。藉由CO吸附降低觸媒活性面積，利用薄膜旋轉電極方法可求得Pt/C觸媒層氫氣氧化的電流密度，進而測得交換電流密度。在高CO覆蓋率下，Pt/C觸媒層的氫氣氧化反應為化學反應與擴散混合控制。本研究測得所製備之27.2wt% Pt/C觸媒的交換電流密度為5mA/cm^2（2A/mg（下標 Pt)）。 Platinum on carbon catalysts used in low-temperature fuel cells were prepared by using colloidal precursor technique. The influences of chemisorbed CO on the hydrogen oxidation reaction (HOR) on the catalyst were investigated by cyclic voltammetry (CV) and the rotating disk electrode (RDE) techniques. The particle size of Pt for 5.4~27.2 wt% Pt/C catalysts prepared, determined by X-ray diffraction (XRD) and transmission electron microscopy (TEM), was in the range of 3.1~8.9 nm, which are slightly larger than that of the commercial Pt/C catalyst. By reducing the electroactive surface area of the catalyst through the adsorption of CO, the current density in the catalyst layer and thus the exchange current density for HOR on the catalyst can be measured using the thin-film RDE methodology. At the higher CO coverage, the HOR in the Pt/C catalyst layer was the case of a mixture of reaction and diffusion control. The exchange current density of the prepared 27.2wt% Pt/C was determined to be 5mA/cm^2 (2A/mg(subscript Pt)).
關聯:	華岡工程學報； 26期 (2010 / 06 / 01) ， P153 - 158
顯示於類別:	[工學院] 學報-華岡工程學報

文件中的檔案:

檔案	描述	大小	格式	瀏覽次數
index.html		0Kb	HTML	362	檢視/開啟

檢視Licence

在CCUR中所有的資料項目都受到原著作權保護.

資料載入中.....